Skip to content
Dallas’s Leading Water Damage Restoration & Mold Remediation Company.

Mold removal help, 24/7

Mold Remediation in Dallas, TX

Mold on a wall, in a closet or behind the air handler? Call (945) 468-7911 and we'll connect you with trusted local mold remediation professionals who find the moisture source, contain the area and remove the mold safely. Below: what the job involves, what it costs, and how Texas's licensing rules protect you.

What's included

  • Finding the moisture source (leak, condensation, humidity)
  • Containment with plastic sheeting and negative air pressure
  • HEPA air filtration during the work
  • Removal of moldy drywall, insulation and other porous materials
  • Cleaning and treatment of hard surfaces
  • Clearance by an independent licensed assessor and your Certificate of Mold Damage Remediation
Mold and water damage on a ceiling around pipework

Why mold is so common in Dallas

Mold needs moisture, a food source and warmth. Dallas mornings average 78% relative humidity, 81% in June (NCEI), and summer nights sometimes stay above 80°F (NWS). Any water that gets in and isn't dried within 24 to 48 hours is likely to grow mold (EPA), and the Dallas pattern is water that gets in quietly: a hail-bruised roof leaking into attic insulation for a season, a slab leak under a kitchen floor as the Blackland clay moves, a pipe that burst in the 2021 freeze and was patched before the framing was dry.

Indoors, add the usual: a clogged AC condensate line soaking a ceiling, an air handler closet that never dries out, a slow leak under a sink. About half of Dallas's housing predates 1980 (City of Dallas), with the original plumbing and roofing to match.

Texas licenses mold work: what that means for you

Texas regulates mold assessment and remediation through the Department of Licensing and Regulation (TDLR). Four rules matter to a Dallas homeowner:

  • A license is required. Nobody may do mold assessment without an assessment license, or mold remediation without a remediation license (Texas Occupations Code 1958.101).
  • The small-area exemption. A license isn't needed where the contamination is less than 25 contiguous square feet (1958.102). Above that, it is licensed work.
  • No assessing and remediating the same project. A license holder may not do both on the same project, and nobody may own an interest in both companies on the same project (1958.155). The rule exists so nobody can find mold and then sell you the fix.
  • You get a certificate. Within 10 days of finishing, the remediator must give you a Certificate of Mold Damage Remediation, including a licensed assessor's statement that the contamination was remediated as the protocol required (1958.154). Keep it: when you sell, buyers are entitled to copies of certificates from the past five years.

Before anyone starts, ask for the license number and check it on the TDLR license search. For patches under 25 square feet on hard surfaces, our guide to cleaning a small patch covers what to do. For the assessor's side of a licensed job, see mold inspection and testing in Dallas.

What mold remediation involves

  1. Find the water. Moisture meters and thermal imaging locate the leak or condensation that fed the mold. Removing mold without fixing the moisture just restarts the clock.
  2. Protocol. For licensed jobs in Texas, a licensed assessment consultant writes the remediation protocol: what to remove, where, how, and what "clean" will mean at clearance (16 TAC 78.100).
  3. Contain the area. Plastic sheeting and negative air pressure stop spores spreading to the rest of the house, with HEPA air scrubbers running.
  4. Remove what can't be cleaned. Moldy drywall, insulation, carpet pad and ceiling tiles are cut out and bagged. EPA guidance is that porous materials with mold growing in them generally have to be discarded (EPA).
  5. Clean hard surfaces and dry. Studs, concrete and other hard materials are cleaned and, where appropriate, treated, and the area is dried to match the rest of the house.
  6. Clearance. A licensed assessment consultant, not the remediator, inspects while the containment is still up and issues a passed clearance report; the remediator then gives you the certificate and before-and-after photos within 10 days (16 TAC 78.140; 78.150). See mold inspection and testing in Dallas.
  7. Rebuild. New drywall, paint and trim, often with mold-resistant board in bathrooms and laundry rooms.

What mold remediation costs in Dallas

Published national ranges run from about $1,200 to $9,000 depending on the source, with averages between $2,300 and $3,500 and per-square-foot figures of roughly $10 to $30 (Fixr, 2025; This Old House, 2026; Bob Vila). The spread is about size and access: a closet wall is at the low end, an attic that has been wet since the last hail storm or a whole air handler system at the high end. In Texas, licensed jobs also carry the assessor's protocol and clearance fees, which buy you an independent sign-off.

Insurance usually covers mold only when it follows a covered water event, and the Texas Department of Insurance notes most home policies don't include mold cleanup and testing after the damaged item is removed (TDI). The estimate comes in writing before any work starts.

Mold and your health

The CDC's summary: for some people, mold can cause a stuffy nose, sore throat, coughing or wheezing, burning eyes or a skin rash; people with asthma or mold allergies may have severe reactions, and people with weakened immune systems or chronic lung disease can get lung infections from mold (CDC). If anyone in the home is in those groups, don't disturb the mold yourself; have it removed, and keep them out of the area until it's done. You don't need to know the type of mold, and the CDC doesn't recommend testing to decide whether to clean it up.

When to call right now

  • Mold covering more than about 10 square feet (the EPA's do-it-yourself limit); above 25 contiguous square feet it's licensed work in Texas
  • Mold that came back after cleaning
  • A musty smell with no visible source
  • Mold after a leak, roof damage, freeze or AC overflow
  • Someone in the home with asthma, allergies or a weakened immune system

Call (945) 468-7911 and we'll connect you with local mold remediation help. If the mold followed water damage that hasn't been dried, start with water damage restoration in Dallas.

Areas served around Dallas

The professionals we work with cover Dallas and the communities around it, including Downtown Dallas, Uptown, Oak Lawn, East Dallas, Lakewood, Oak Cliff, Preston Hollow, Lake Highlands, Highland Park, University Park, Richardson, Plano, Garland, Irving, Mesquite, Carrollton, Addison. Not listed? Call anyway and we'll find the nearest help.

Questions

Mold Remediation in Dallas: your questions

Do I need a licensed mold remediator in Dallas?

If the contamination is 25 contiguous square feet or more, yes: Texas requires a TDLR mold remediation license, a written protocol from a licensed assessor and a clearance inspection. Under 25 square feet you may clean it yourself, though anything on drywall or after a leak is worth a professional look. Check any license on the TDLR site.

Can the same company test for mold and remove it?

Not in Texas. A license holder may not perform both assessment and remediation on the same project, and nobody may own both companies on the same project. If one firm offers both on your job, that is a red flag.

What is the Certificate of Mold Damage Remediation?

A document the remediator must give you within 10 days of finishing, with a licensed assessor's statement that the mold was remediated as the protocol required. Keep it with the house papers: buyers are entitled to copies of certificates issued in the five years before a sale.

Does insurance cover mold remediation?

Often only when the mold results from a covered sudden water event, and many policies cap mold coverage. Mold from humidity, condensation or an old leak is usually excluded. Check your policy and document everything.

Should I get the mold tested first?

If you can see mold, the EPA says sampling is usually unnecessary: it needs removing whatever the type. In Texas, though, a licensed job starts with an assessor's protocol and ends with their clearance, so an assessor is part of the process. See our Dallas mold inspection page.

How long does mold remediation take?

A single room is usually one to three days plus drying time, then the clearance inspection. Attics, air handler systems and whole-floor jobs take longer. Containment stays up until the area passes clearance.

Google reviews

What customers say about Damp Solving

Genuine Google reviews from people who called Damp Solving, across all of our offices.

Call Now 24/7